Hello Petr,
are you using the
GRHydro::reconstruct_Wv = yes
parameter? I need to use it in my accretion disk runs when using the Ideal_Fluid EOS...Using the polytrope this parameter wasn't needed if I recall correctly..
hope this helps..
best wishes,
Vassili
On Tue, Nov 26, 2013 at 6:00 PM, Petr Tsatsin ptsatsin@my.fau.edu wrote:
Hello, I've recently tried to perform simulation of the binary neutron stars started from Meudon initial data. I've encountered a following problem. I can run the simulations without any problems when I use polytropic EOS. However, when I switch to Gamma-Law simulations crushed soon after start somewhere in the conversion of primitive quantities to conserved quantities. The typical log is look like this one:
WARNING[L1,P28] (GRHydro): Con2Prim failed; stopping the code. WARNING[L1,P28] (GRHydro): Even with mesh refinement, this point is not restricted from a finer level, so this is really an error WARNING[L1,P28] (GRHydro): on carpet reflevel: 2 WARNING[L1,P28] (GRHydro): xyz location: 12.00000 0.000000 -2.000000 WARNING[L1,P28] (GRHydro): radius: 12.16553 WARNING[L1,P28] (GRHydro): hydro_excision_mask, C2Pfailed: 0 1.0000000 WARNING[L1,P28] (GRHydro): rho eps press w_lorentz: 0.1047685E-08 0.5280317E-01 0.5532109E-10 1.013257 WARNING[L1,P28] (GRHydro): velocities: -0.3371566E-02 0.1176264 -0.3492353E-01 WARNING[L1,P28] (GRHydro): dens tau: 0.2037191E-08 0.1388378E-09 WARNING[L1,P28] (GRHydro): scon: -0.2835004E-10 0.4723716E-09 -0.1051106E-09 WARNING[L1,P28] (GRHydro): 3-metric: 1.420906 -0.7104738E-01 -0.2077218E-01 1.770598 0.4372303E-01 1.468061 WARNING[L1,P28] (GRHydro): lapse, shift: 0.8118283 0.1691328E-01 -0.3824454E-01 -0.5210642E-03 WARNING level 0 in thorn GRHydro processor 28 host c559-402.stampede.tacc.utexas.edu (line 2404 of GRHydro_Con2Prim.F90): -> Aborting. cactus_SBNS: /work/02566/tsatsin/Cactus/arrangements/Carpet/Carpet/src/helpers.cc:314: int Carpet::Abort(const _cGH *, int): Assertion `0' failed.
The parameter files for "polytropic" runs and "Gamma-Law" are identical except, obviously, the parameters controlling the EOS. I was wondering if somebody experienced similar problems before? I would be very grateful for any help and suggestions. I also include the some relevant parameters I used for "Gamma-law" EOS below. May be I'm missing some important parameters or values are not properly set?
# Hydro paramters ActiveThorns = "EOS_Omni" EOS_Omni::poly_k = 123.6 EOS_Omni::poly_gamma = 2.0 EOS_Omni::gl_k = 123.6 EOS_Omni::gl_gamma = 2.0
ActiveThorns = "GRHydro"
GRHydro::initial_Gamma = 2.0
HydroBase::evolution_method = "GRHydro"
#GRHydro::riemann_solver = "Marquina" GRHydro::riemann_solver = "HLLE" GRHydro::GRHydro_eos_type = "General" GRHydro::GRHydro_eos_table = "Ideal_Fluid" GRHydro::recon_method = "ppm" GRHydro::GRHydro_stencil = 3 GRHydro::bound = "flat" GRHydro::rho_abs_min = 1.e-10 #GRHydro::GRHydro = 18 # Tmunu(10), rho,press,eps,w_lorentz,vel, tau #GRHydro::GRHydro = 10 # gij(6), alpha, beta(3)
GRHydro::c2p_reset_pressure = "yes" grhydro::grhydro_c2p_warnlevel = 0 grhydro::grhydro_c2p_warn_from_reflevel = 2
ActiveThorns = "GenericFD NewRad" ActiveThorns = "ML_BSSN ML_BSSN_Helper" ActiveThorns = "ML_ADMConstraints"
Thank you and Happy Thanksgiving. Petr. -- Petr Tsatsin Graduate Student - Department of Physics Charles E. Schmidt College of Science Florida Atlantic University (561)-297-3386 cell: 1-561-299-8048 ptsatin@fau.edu, ptsatsin@gmail.com
Users mailing list Users@einsteintoolkit.org http://lists.einsteintoolkit.org/mailman/listinfo/users